Exactly how to Install a Tub (Step By Step).
Exactly how to Install a Tub (Step By Step).
Blog Article
Just how do you really feel on the subject of How to Install a Bathtub Yourself?
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is conveniently available, the task can move immediately; if you have to open up a wall to eliminate the old tub as well as place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub and also set in the new one. See to it you have certified yourself for the task and also are comfortable trying it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This post will help you set up a brand-new bathtub in your shower room if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product checklist should comprise the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to avoid pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are handy in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub till the spirit level reviews degree.
To install faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints as well as new pipework for leakages and also tighten them if required. Load the bathtub and additionally check the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait until the tub has actually been used at the very least once as this will resolve it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Protect the faucet in place with the producer offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly available on the market. It is advisable to fit the tiles using waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that blog posting on How to Install a Bathtub when browsing on the search engines. Do you know another person who is curious about the topic? Take a moment to share it. Thank-you for taking the time to read it.
Maintenance Sign-Up Report this page